10-minute DIY: an easy-to-make snoot for light painting

This is admittedly a rather specific DIY project, but hopefully it fills a niche, however small that might be. And the twenty-three people who want to do this might be really happy.

I cannot take credit for this fine design. Night photographer Tyler Heibeck told me how to do this, showing this to me when we were traveling in Iceland. But it’s easy to do. It’s simply sanding and gluing. If I can do it, you can do it. And probably better.

The specific design I’ll describe is for a ProtoMachines LED2 handheld light painting device. It has threads so you can screw them on. And so do a lot of lights. But even if they don’t, as long as you have a piece that attaches to your light source and you can glue modifiers on to that, you can run with this idea.


What’s a snoot and how do you use one?

In photography, it’s a tube or something similar that allows you to direct light. You can fit one over a studio light or a portable flash or a flashlight. Here, it’s most similar to a flashlight. This allows you to control the direction and radius of the light beam. I’ve done that with the above photo of the bus.

I use this for various reasons. The most common for me is to light paint a headlight so it looks like it’s on. This is great fun.

Above: A finished snoot attached to a ProtoMachines LED2 light painting device.


What you need:

Aluminum Step Up Filter Ring. These are usually used for things like UV filters on camera lens. This one is a 58-77MM thread.

Bushing for connecting two pipes with different diameters I used a 2″ x 1-1/2″ bushing here. 

Coupling for connecting two pipes with the same diameter in a straight run. This is for connecting the long tube to the bushing. This particular one is a 2″ coupling on the exterior, but it fits a 1-1/2″ pipe.

ABS pipe or something similar. The particular one I purchased before is not sold any more, but any ABS or PVC pipe should work. 

J-B Weld 8265S Original Cold-Weld Steel Reinforced Epoxy – 2 oz. This is a two-part epoxy system that is designed as an alternative to torch welding. It’s bizarrely strong. One bottle has a sort of liquid steel, and the other bottle has a fluid that chemically hardens the steel so that it creates a bond that is stronger than steel. I can attest to it lasting through for years of abuse.

3M Garnet Sandpaper, Very Fine Grit, 9-Inch by 11-Inch, 5-Sheet


Sanding and gluing

Step 1 – Sanding. First, sand all the surfaces that you will be gluing. Roughen them up and then wipe off the dust.

You really only need to glue the aluminum step-up ring to the bushing (shown above after it was sanded). That’s what I did for my first snoot, and that lasted without incident for four years before I left it in an airplane hangar. However, if you wish to glue everything else as I’ve done this time, sand all the surfaces first.

Step 2: Gluing: Take the J-B Weld and add the steel to one side and the hardener to the other side. Apply this with Q-tips or something similar. You can also mix them together on one surface, but I found it was easier and less messy to apply them separately. Above is the step-up ring and the bushing just before I glued them together.

Step 3 – More gluing (optional): Remember, you don’t have to glue the other pieces if you don’t want to. Here, from the bottom up, you can see the step-up ring glued to the bushing, and then the coupling has been inserted into the bushing. I really didn’t need to glue the coupling into the bushing. It is a tight fit and doesn’t come apart. But when you have extra glue, why not?

Above: I’ve now glued the ABS (similar to PVC) pipe into the coupling. This will make for a good, solid fit. Again, you do not need to glue this. In fact, if you wish to swap up different lengths of ABS pipe, it’s a good idea not to glue it! Your choice.


Does it have to be black?

No, absolutely not. But people who light paint frequently walk through the frame. We like to use dark things to minimize the chance of it showing in the photo or reflecting something. We wear dark clothes and use dark things. So it is with this snoot. But if you wanted, you could get most of these parts in white. That would certainly make getting the pipe easier, as you could use PVC pipe, which is generally found in white. ABS pipe is black. It also tends to be a little more solid and can withstand more shock, which probably isn’t that crucial unless you slam the car door on it or something. Well, okay, that sounds like something I might do, so maybe that is more crucial!


An even easier, cheaper snoot

Although this takes only about ten minutes to do, you can certainly use a cruder, simpler snoot. For instance, you can use a heavy-duty cardboard packing tube, available just about anywhere. The advantage is that it is cheap.

Two disadvantages of a heavy-duty cardboard packing tube

One disadvantage is that it “leaks” light slightly between the tube and the flashlight and can show up if you walk across the frame or otherwise need to get close to the headlight. This was the case in the photo of the bus above.

The other disadvantage is that you have to use both hands. In reality, this second point isn’t really that big of a deal, but it bears mentioning.



I hope this helps! Again, I want to emphasize that if you can find one piece that attaches to your light, you can simply, uh, modify this light modifier to suit your needs! I hope this helps! If you can, please leave a link to any similar DIY light modifier project that you’ve done in the comments!



Head on over to the Ken Lee Photography website to purchase books or look at night photography and long exposure photos.  My latest book, “Abandoned Southern California: The Slowing of Time” is available there and Amazon, Barnes and Noble, Target, Booktopia, Books A Million, IBS, and Aladin. If you enjoy the book, please leave a nice review.

Ken Lee Photography Facebook Page (poke your head in, say hi, and “like” the page if you would, uh, like)

Behind the Shot video podcast – interview February 2020

Conversation about night photography and my book with Lance Keimig of National Park At Night

A Photographer Captures Haunting Nighttime Images of Abandoned Buildings, Planes, and Cars in the American Southwest – Business Insider by Erin McDowell
A Photographer Explores Southern California’s Desert Ruins – Los Angeles Magazine article by Chris Nichols